全自動晾茬機采用兩機轉子，粉碎物料更加細致，沒有篩網規格不容易堵塞。即便是老式?jīng)霾鐧C(jī)粉碎不上的高低溫物料，也可以輕輕松松粉碎，不堵塞。主要特點是低成本，生產量高，粉碎好用，釀酒廠涼茬機，可調式內部錘頭總數和部位來源于在操縱進料粒度。
The fully automatic stubble drying machine adopts two rotors, which makes the crushing of materials more detailed and does not have a mesh size that is easy to block. Even high and low temperature materials that cannot be crushed by old-fashioned stubble cutters can be easily crushed without clogging. The main characteristics are low cost, high production capacity, easy to use crushing, brewery cooling stubble machine, adjustable internal hammer head, total number and parts come from controlling the feed particle size.
全自動晾茬機是將攤晾、加漿、加曲、攪拌、卸料等工序一次性完成，攤晾效果好，在攤晾過程中設置多個攪拌裝置，使涼茬在攤晾過程中松散、不易結坨，加漿、下曲均勻，數量可調節。那要如何穩定的使用自動涼茬機呢？
The fully automatic stubble drying machine completes the processes of spreading, adding slurry, adding koji, stirring, and unloading in one go. The spreading effect is good, and multiple mixing devices are set up during the spreading process to make the cool stubble loose and not easy to clump during the spreading process. The addition of slurry and koji is uniform, and the quantity can be adjusted. How to use an automatic stubble cooler stably?
一、安裝前應先查看自動涼茬機各部位，零件是否有松動現象，如發現，需修理后方可安裝。
1、 Before installation, check all parts of the automatic stubble cooler to see if there are any loose parts. If found, repair is necessary before installation.
二、安裝時，打茬機跑車輪與道軌間隙以打茬機與軌跡來回跑動時為規范。
2、 When installing, the gap between the stubble machine's running wheel and the track is standardized when the stubble machine runs back and forth with the track.
三、打茬機安裝結束后，需要行試工作五分鐘左右，查看各部位是否有雜音現象出現，如發現雜音應泊車檢修，待試工作正常后，方可投入正常生產運用。
3、 After the installation of the stubble cutting machine is completed, it is necessary to conduct a trial operation for about five minutes to check for any noise in various parts. If any noise is found, it should be parked for maintenance. After the trial operation is normal, it can be put into normal production and use.
四、運用過程中，應經常留意有無異常動靜，轟動是否加大，如發現雜音應及時泊車檢修。
4、 During the use process, it is necessary to regularly pay attention to any abnormal movements and increase the noise. If any noise is found, it should be promptly parked for maintenance.
五、打茬機投入運用后，應定期查看螺栓有無松動，零部件有無損壞，如發現應根據具體情況檢修或更換零部件。
5、 After the stubble cutting machine is put into use, it should be regularly checked for looseness of bolts and damage to components. If found, it should be repaired or replaced according to the specific situation.
六、在運用過程中，注油部位應定期注油，一般每三個月注黃油一次，以確保打茬機各傳動部位潤滑正常，減少磨損。
6、 During operation, the oil injection area should be regularly lubricated, usually with butter every three months, to ensure normal lubrication of all transmission parts of the stubble machine and reduce wear.
七、自動涼茬機若長時間停用從頭投入生產運用時，要從頭進行查看，并通過試車工作正常后再投入生產運用。
7、 If the automatic stubble cooling machine is stopped for a long time and put into production again, it should be checked from the beginning and put into production again after the test run is normal.
This article is supported by a fully automatic stubble cooler. For more detailed and exciting content, please click on our website http://www.youjizz-sex.com We will wholeheartedly provide you with satisfactory service.
自動售酒機 2024-07-25 
